SUMARIzATION

Memperkecil routing table membuat proses pencarian menjadi lebih efisien, karena lebih sedikit rute yang dicari.

1. 172.16.0.0/16
2. 172.17.0.0/16
3. 172.18.0.0/16
4. 172.19.0.0/16

Dapat disederhanakan menjadi jaringan 172.16.0.0/14, karena semua rute menggunakan interface keluaran yang sama, sehingga dapat diringkas menjadi sebuah jaringan 172.16.0.0 dengan subnet mask 255.252.0.0, dan ini disebut summary route.

ROUTER RIP Version 2

Langkah-langkah pengkonfigurasian jaringan :

1. Mengganti kabel konektor yang belum sesuai, ganti dan sesuaikan semua kabel konektor sesuai    dengan perangkat yang dihubungkan. Untuk mengganti kabel konektor kita cek terlebih dahulu apakah telah terdapat port yang sesuai dengan port yang dibutuhkan kabel.

2. Kita lakukan pengaturan ulang pada setiap router, yaitu kita lakukan pemberian IP dan pengaturan router dengan router RIP. Router RIP yang kita gunakan adalah router RIP versi2
IP yang kita berikan pada setiap router adlah sebagai berikut :

Sedangkan untuk konfoigurasi router dapat dilihat pada perintah dibawah ini :

Pada Router Chicago 1

Chicago1>en

Chicago1#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

Chicago1(config)#int fa 0/0

Chicago1(config-if)#ip add 192.168.10.1 255.255.255.224

Chicago1(config-if)#no shut

Chicago1(config-if)#exit

Chicago1(config)#int s1/1

Chicago1(config-if)#ip add 172.10.16.1 255.255.255.252

Chicago1(config-if)#clock rate 9600

Chicago1(config-if)#no shut

Chicago1(config-if)#exit

Chicago1(config)#

%SYS-5-CONFIG_I: Configured from console by console

Chicago1#

Chicago1#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

Chicago1(config)#router rip

Chicago1(config-router)#version

% Incomplete command.

Chicago1(config-router)#version 2

Chicago1(config-router)#no auto

Chicago1(config-router)#no auto-summary

Chicago1(config-router)#network 192.168.10.0

Chicago1(config-router)#network 172.10.16.0

Chicago1(config-router)#no

Chicago1(config-router)#ex

Chicago1(config)#e

Pada Router Chicago

Chicago>en

Chicago#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

Chicago(config)#int fa 0/0

Chicago(config-if)#ip add 192.168.20.1 255.255.255.224

Chicago(config-if)#no shut

Chicago(config-if)#exit

Chicago(config)#int s 1/1

Chicago(config-if)#ip add 172.10.16.2 255.255.255.252

Chicago(config-if)#no shut

%LINK-5-CHANGED: Interface Serial1/1, changed state to up

Chicago(config-if)#

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/1, changed state to up

Chicago(config-if)#exit

Chicago(config)#int s 1/0

Chicago(config-if)#ip add 172.16.10.1 255.255.255.252

%DUAL-5-NBRCHANGE: IP-EIGRP 10: Neighbor 10.10.254.250 (Serial1/0) is down: interface downChicago(config-if)#no shut

Chicago(config-if)#exit

Chicago(config)#

Chicago#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

Chicago(config)#router rip

Chicago(config-router)#version 2

Chicago(config-router)#no auto

Chicago(config-router)#no auto-summary

Chicago(config-router)#network 192.168.20.0

Chicago(config-router)#network 172.10.16.0

Chicago(config-router)#network 172.16.10.0

Chicago(config-router)#ex

Chicago(config)#

Pada Router Denver

Denver>en

Denver#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

Denver(config)#int s1/0

Denver(config-if)#ip add 172.16.10.2 255.255.255.252

Denver(config-if)#clock rate 9600

Denver(config-if)#no shut

Denver(config-if)#exit

Denver(config)#int s1/2

Denver(config-if)#ip add 180.10.10.1 255.255.255.252

Denver(config-if)#clock rate 9600

Denver(config-if)#no shut

%LINK-5-CHANGED: Interface Serial1/2, changed state to up

Denver(config-if)#

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to up

Denver(config-if)#exit

Denver(config)#int s1/1

Denver(config-if)#ip add 200.10.10.1 255.255.255.252

Denver(config-if)#no shut

Denver(config-if)#exit

Denver(config)#int s1/3

Denver(config-if)#ip add 200.10.20.1 255.255.255.252

Denver(config-if)#clock rate 9600

Denver(config-if)#no shut

%LINK-5-CHANGED: Interface Serial1/3, changed state to up

Denver(config-if)#

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/3, changed state to up

Denver(config-if)#exit

Denver(config)#exit

Denver#

Denver#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

Denver(config)#router rip

Denver(config-router)#version 2

Denver(config-router)#no au

Denver(config-router)#no auto-summary

Denver(config-router)#network 172.16.10.0

Denver(config-router)#network 180.10.10.0

Denver(config-router)#network 200.10.10.0

Denver(config-router)#network 200.10.20.0

Denver(config-router)#ex

Denver(config)#

Pada Router Dallas

Dallas>en

Dallas#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

Dallas(config)#int s0/1

Dallas(config-if)#ip add 200.10.10.2 255.255.255.252

Dallas(config-if)#clock rate 9600

Dallas(config-if)#no shut

Dallas(config-if)#exit

Dallas(config)#int s0/0

Dallas(config-if)#ip add 210.15.20.1 255.255.255.252

Dallas(config-if)#clock rate 9600

Dallas(config-if)#no shut

Dallas(config-if)#exit

Dallas(config)#int fa 0/0

Dallas(config-if)#ip add 192.168.30.1 255.255.255.224

Dallas(config-if)#no shut

Dallas(config-if)#exit

Dallas(config)#exit

Dallas#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

Dallas(config)#router rip

Dallas(config-router)#version 2

Dallas(config-router)#no au

Dallas(config-router)#no auto-summary

Dallas(config-router)#network 200.10.10.0

Dallas(config-router)#network 200.15.20.0

Dallas(config-router)#network 192.168.30.0

Dallas(config-router)#ex

Dallas(config)#

Pada Router Denver 1

Denver1>en

Denver1#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

Denver1(config)#int s1/2

Denver1(config-if)#ip add 180.10.10.2 255.255.255.252

Denver1(config-if)#no shut

Denver1(config-if)#exit

Denver1(config)#int fa0/0

Denver1(config-if)#ip[ add 192.168.40.1 255.255.255.224

^

% Invalid input detected at ‘^’ marker.

Denver1(config-if)#ip add 192.168.40.1 255.255.255.224

Denver1(config-if)#no shut

Denver1(config-if)#exit

Denver1(config)#

%SYS-5-CONFIG_I: Configured from console by console

Denver1#

Denver1#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

Denver1(config)#router rip

Denver1(config-router)#version 2

Denver1(config-router)#no au

Denver1(config-router)#no auto-summary

Denver1(config-router)#network 180.10.10.0

Denver1(config-router)#network 192.168.40.0

Denver1(config-router)#ex

Denver1(config)#

Pada Router Denver 2

Denver2>en

Denver2#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

Denver2(config)#int s1/3

Denver2(config-if)#ip add 200.10.20.2 255.255.255.252

Denver2(config-if)#no shut

Denver2(config-if)#exit

Denver2(config)#int fa0/0

Denver2(config-if)#ip add 192.168.50.1

% Incomplete command.

Denver2(config-if)#ip add 192.168.50.1 255.255.255.224

Denver2(config-if)#no shut

Denver2(config-if)#exit

Denver2(config)#exit

Denver2#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

Denver2(config)#router rip

Denver2(config-router)#version 2

Denver2(config-router)#no au

Denver2(config-router)#no auto-summary

Denver2(config-router)#network 200.10.20.0

Denver2(config-router)#network 192.168.50.0

Denver2(config-router)#ex

Denver2(config)#

Pada Router Phoenix 1

Phoenix1>en

Phoenix1#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

Phoenix1(config)#int s0/0

Phoenix1(config-if)#ip add 210.15.20.2 255.255.255.252

Phoenix1(config-if)#no shut

Phoenix1(config-if)#exit

Phoenix1(config)#int s0/1

Phoenix1(config-if)#ip add 240.20.10.1 255.255.255.252

Not a valid host address – 240.20.10.1

Phoenix1(config-if)#ip add 220.20.10.1 255.255.255.252

Phoenix1(config-if)#clock rate 9600

Phoenix1(config-if)#no shut

%LINK-5-CHANGED: Interface Serial0/1, changed state to down

Phoenix1(config-if)#exit

Phoenix1(config)#int fa 0/0

Phoenix1(config-if)#ip add 192.168.60.1 255.255.255.224

Phoenix1(config-if)#no shut

Phoenix1(config-if)#exit

Phoenix1(config)#exit

Phoenix1#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

Phoenix1(config)#router rip

Phoenix1(config-router)#version 2

Phoenix1(config-router)#no au

Phoenix1(config-router)#NO

Phoenix1(config-router)#no

Phoenix1(config-router)#no au

Phoenix1(config-router)#no auto-summary

Phoenix1(config-router)#network 210.15.20.0

Phoenix1(config-router)#network 220.20.10.0

Phoenix1(config-router)#192.168.60.0

^

% Invalid input detected at ‘^’ marker.

Phoenix1(config-router)#network 192.168.60.0

Phoenix1(config-router)#ex

Pada Router Phoenix 2

Phoenix2>en

Phoenix2#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

Phoenix2(config)#int 0/1

^

% Invalid input detected at ‘^’ marker.

Phoenix2(config)#int s0/1

Phoenix2(config-if)#ip add 220.20.10.2 255.255.255.252

Phoenix2(config-if)#no shut

%LINK-5-CHANGED: Interface Serial0/1, changed state to up

Phoenix2(config-if)#

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1, changed state to up

Phoenix2(config-if)#xit

^

% Invalid input detected at ‘^’ marker.

Phoenix2(config-if)#exit

Phoenix2(config)#int fa 0/0

Phoenix2(config-if)#ip add 192.168.70.1 255.255.255.224

Phoenix2(config-if)#no shut

Phoenix2(config-if)#exit

Phoenix2(config)#exit

Phoenix2#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

Phoenix2(config)#router rip

Phoenix2(config-router)#version 2

Phoenix2(config-router)#no au

Phoenix2(config-router)#no auto-summary

Phoenix2(config-router)#network 220.20.10.0

Phoenix2(config-router)#network 192.168.70.0

Phoenix2(config-router)#ex

Phoenix2(config)#

3. Setelah selesai melakukan konfigurasi tahap selanjutnya adalah pemberian IP pada setiap PC

PC-0

PC-1

 PC-2

 PC-3

 PC-4

 PC-5

 PC-6

Setelah selesai maka semuanya dapat saling berkomunikasi

Termologi dan Tabel EIGRP

             Dalam menyimpan informasi jaringan dari proses update dan dukungan terhadap proses konvergensi yang cepat, EIGRP menggunakan beberapa tabel. Router dengan EIGRP menyimpan informasi rute dan topologi dalam RAM sehingga dapat dilakukan perubahan secara cepat. EIGRP memilihara 3 (tiga) tabel yang saling terkoneksi, yaitu :
1. Neighbor table
2. Topology table
3. Routing table

Neighbor Table
Neighbor table berisi informasi mengenai daftar router yang directly connected dengannya. EIGRP mencatat alamat terbaru dari router tetangga yang ditemukan beserta interface yang terkoneksi dengannya.

Ketika router tetangga mengirimkan sebuah hello packet, hal itu berkaitan dengan hold time. Hold time adalah lama waktu yang diperlukan oleh router dalam menjaga informasi mengenai keberadaan router tetangganya. Jika hello packet tidak diterima selama kurun waktu hold time, maka router tetangga dianggap down dan DUAL akan mengkalkulasi ulang topologi jaringan terbaru.
Cepat lambatnya proses konvergensi tergantung pada keakuratan informasi yang diberikan oleh router tetangga, sehingga tabel ini dapat dikatakan sebagai tabel penting dalam proses operasi EIGRP.

Topology table
Topology table berisi informasi mengenai daftar keseluruhan rute yang berasal dari informasi yang dipelajari dari masing-masing router EIGRP tetangga. DUAL mengambil informasi dari neighbor table dan topology table kemudian menghitung cost terendah bagi rute ke tiap-tiap jaringan.

Topology table mengidentifikasikan empat rute utama yang loop-free untuk setiap satu jaringan tujuan. Successor route ini akan muncul di routing table. EIGRP membagi beban (load balance), atau mengirimkan paket ke tujuan menggunakan lebih dari satu jalur. Dia membagi beban menggunakan rute-rute successor secara equal cost maupun unequal cost. Fitur ini menjaga agar tidak terjadi overloading paket pada satu rute.

Backup routes, dikenal dengan sebutan feasible successors, muncul di topology table namun tidak di routing table. Apabila rute utama gagal, feasible successor akan menjadi successor route. Backup ini terjadi sepanjang feasible successor memiliki reported distance lebih pendek dibandingkan dengan feasible successor distance saat ini ke jaringan tujuan.

- Rute Status = apakah rute stabil dan siap untuk digunakan (pasif) atau sedang dihitung kembali oleh DUAL (aktif)
- Jarak Layak = terendah dihitung metrik ke tujuan.
- Jarak Dilaporkan = jarak ke tujuan seperti yang dilaporkan oleh router tetangga.
- Tujuan jaringan = alamat jaringan tujuan.
- Jumlah penerus = jumlah biaya jalur yang sama dengan metrik terendah ke tujuan.
- Hop alamat berikutnya atau penggantinya alamat = ip dari interface hop berikutnya.
- Hop alamat berikutnya atau penerus layak alamat = ip dari interface hop berikutnya untuk penerus layak.
- Jarak layak penerus layak = metrik dihitung untuk tujuan melalui penerus layak.
- Jarak yang dilaporkan penerus layak = jarak ke tujuan seperti yang dilaporkan oleh router tetangga.
- Interface = antarmuka outbound bahwa lalu lintas menggunakan untuk keluar router ke tujuan.

Routing Table
Jika topology table berisi informasi mengenai beberapa jalur yang mungkin dilalui menuju ke jaringan tujuan, maka routing table hanya menampilkan jalur terbaik saja yang dikenal dengan istilah successor routes.

EIGRP menampilkan informasi mengenai rute dalam 2 bentuk:
Routing table merancang rute yang dipelajari melalui EIGRP dengan kode D. Sementara EIGRP menandai baik rute dinamis atau statis yang dipelajarinya dari routing protocols lainnya atau dari jaringan EIGRP luar dengan kode D EX atau external, karena dia tidak murni berasal asli dari router EIGRP dalam AS yang sama.

TUGAS JARKOM 3 TEORI (ROUTING STATIC)

1. MEMBERI NAMA HOSTNAME DAN MEMASUKAN IP ADDRESS

Ø  ROUTER 1

Router>en

Router#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)#hostname R1

R1(config)#int fa0/0

R1(config-if)#ip add 172.16.3.1 255.255.255.0

R1(config-if)#no shut

R1(config-if)#exit

R1(config)#int s2/0

R1(config-if)#ip add 172.16.2.1 255.255.255.0

R1(config-if)#clock rate 64000

R1(config-if)#no shut

Ø  ROUTER 2

Router>en

Router#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)#hostname R2

R2(config)#int fa0/0

R2(config-if)#ip add 172.16.1.1 255.255.255.0

R2(config-if)#no shut

R2(config-if)#exit

R2(config)#int s2/0

R2(config-if)#ip add 172.16.2.2 255.255.255.0

R2(config-if)#no shut

R2(config)#int s3/0

R2(config-if)#ip add 192.168.1.2 255.255.255.0

R2(config-if)#clock rate 64000

R2(config-if)#no shut

Ø  ROUTER3

Router>en

Router#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)#hostname R3

R3(config)#int fa 0/0

R3(config-if)#ip add 192.168.2.1 255.255.255.0

R3(config-if)#no shut

R3(config-if)#exit

R3(config)#int s3/0

R3(config-if)#ip add 192.168.1.1 255.255.255.0

R3(config-if)#no shut

2. MENGENALKAN MASING-MASING JARINGAN DENGAN MENGGUNAKAN ROUTER STATIS

Ø  ROUTER1

R1#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

R1(config)#ip route 0.0.0.0 0.0.0.0 s2/0

R1(config)#exit

%SYS-5-CONFIG_I: Configured from console by console

R1#wr mem

Building configuration...

[OK]

Ø  ROUTER2

R2#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

R2(config)#ip route 172.16.3.0 255.255.255.0 s2/0

R2(config)#ip route 192.168.2.0 255.255.255.0 s3/0

R2(config)#^Z

%SYS-5-CONFIG_I: Configured from console by console

R2#wr mem

Building configuration...

[OK]

Ø  ROUTER3

R3#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

R3(config)#ip route 0.0.0.0 0.0.0.0 s3/0

R3(config)#exit

%SYS-5-CONFIG_I: Configured from console by console

R3#wr mem

Building configuration...

[OK]

3. MEMERIKSA KONEKSI DENGAN PERINTAH PING

                    

4. MEMERIKSA KONEKSI DENGAN PERINTAH TRACEROUTE

Ø  ROUTER1

R1#traceroute 172.16.1.0

Type escape sequence to abort.

Tracing the route to 172.16.1.0

  1   172.16.2.2      31 msec   31 msec   32 msec  

R1#traceroute 192.168.2.0

Type escape sequence to abort.

Tracing the route to 192.168.2.0

  1   172.16.2.2      31 msec   32 msec   31 msec  

  2   192.168.1.1     47 msec   62 msec   62 msec  

Ø  ROUTER2

R2#traceroute 192.168.2.0

Type escape sequence to abort.

Tracing the route to 192.168.2.0

  1   192.168.1.1     47 msec   32 msec   16 msec  

R2#traceroute 172.16.3.0

Type escape sequence to abort.

Tracing the route to 172.16.3.0

  1   172.16.2.1      31 msec   32 msec   31 msec  

Ø  ROUTER3

R3#traceroute 172.16.1.0

Type escape sequence to abort.

Tracing the route to 172.16.1.0

  1   192.168.1.2     31 msec   32 msec   31 msec  

R3#traceroute 172.16.3.0

Type escape sequence to abort.

Tracing the route to 172.16.3.0

  1   192.168.1.2     31 msec   31 msec   31 msec  

  2   172.16.2.1      47 msec   63 msec   47 msec  

5. MEMERIKSA KONEKSI DENGAN MENGGUNAKAN PERINTAH SHOW IP ROUTE

Ø  ROUTER1

R1#show ip route

Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP

       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area

       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2

       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP

       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area

       * - candidate default, U - per-user static route, o - ODR

       P - periodic downloaded static route

Gateway of last resort is 0.0.0.0 to network 0.0.0.0

     172.16.0.0/24 is subnetted, 2 subnets

C       172.16.2.0 is directly connected, Serial2/0

C       172.16.3.0 is directly connected, FastEthernet0/0

S*   0.0.0.0/0 is directly connected, Serial2/0

Ø  ROUTER2

R2#show ip route

Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP

       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area

       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2

       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP

       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area

       * - candidate default, U - per-user static route, o - ODR

       P - periodic downloaded static route

Gateway of last resort is not set

     172.16.0.0/24 is subnetted, 3 subnets

C       172.16.1.0 is directly connected, FastEthernet0/0

C       172.16.2.0 is directly connected, Serial2/0

S       172.16.3.0 is directly connected, Serial2/0

C    192.168.1.0/24 is directly connected, Serial3/0

S    192.168.2.0/24 is directly connected, Serial3/0

Ø  ROUTER3

R3#show ip route

Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP

       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area

       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2

       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP

       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area

       * - candidate default, U - per-user static route, o - ODR

       P - periodic downloaded static route

Gateway of last resort is 0.0.0.0 to network 0.0.0.0

C    192.168.1.0/24 is directly connected, Serial3/0

C    192.168.2.0/24 is directly connected, FastEthernet0/0

S*   0.0.0.0/0 is directly connected, Serial3/0

6. MEMERIKSA KONEKSI DENGAN MENGGUNAKAN PERINTAH SHOW IP INTERFACE BRIEF

Ø  ROUTER1

R1#show ip interface brief

Interface                       IP-Address      OK? Method Status                                    Protocol

 FastEthernet0/0        172.16.3.1      YES manual up                                                    up

 FastEthernet1/0        unassigned      YES manual administratively down        down

 Serial2/0                       172.16.2.1      YES manual up                                                    up

 Serial3/0                       unassigned      YES manual administratively down       down

 FastEthernet4/0        unassigned      YES manual administratively down       down

 FastEthernet5/0        unassigned      YES manual administratively down       down

Ø  ROUTER2

R2#show ip interface brief

Interface                      IP-Address      OK? Method Status                                    Protocol

 FastEthernet0/0        172.16.1.1      YES manual up                                             up

 FastEthernet1/0        unassigned      YES manual administratively down      down

 Serial2/0                     172.16.2.2      YES manual up                                                     up

 Serial3/0                     192.168.1.2     YES manual up                                                   up

 FastEthernet4/0        unassigned      YES manual administratively down     down

 FastEthernet5/0        unassigned      YES manual administratively down     down

Ø  ROUTER3

R3#show ip interface brief

Interface                       IP-Address      OK? Method Status                                  Protocol

 FastEthernet0/0        192.168.2.1     YES manual up                                           up

 FastEthernet1/0        unassigned      YES manual administratively down      down

 Serial2/0                     unassigned      YES manual administratively down      down

 Serial3/0                     192.168.1.1     YES manual up                                                  up

 FastEthernet4/0        unassigned      YES manual administratively down     down

 FastEthernet5/0        unassigned      YES manual administratively down     down

7. MEMERIKSA KONEKSI DENGAN MENGGUNAKAN PERINTAH SHOW CDP NEIGHBORS DETAIL
   
   

Ø  ROUTER1

R1#show cdp neighbors detail

Device ID: Switch

Entry address(es):

Platform: cisco PT3000, Capabilities: Switch

Interface: FastEthernet0/0, Port ID (outgoing port): FastEthernet0/1

Holdtime: 165

Version :

Cisco Internetwork Operating System Software

IOS (tm) PT3000 Software (PT3000-I6Q4L2-M), Version 12.1(22)EA4, RELEASE SOFTWARE (fc1)

Copyright (c) 1986-2006 by cisco Systems, Inc.

Compiled Fri 12-May-06 17:19 by pt_team

advertisement version: 2

Duplex: full

---------------------------

Device ID: R2

Entry address(es):

  IP address : 172.16.2.2

Platform: cisco PT1000, Capabilities: Router

Interface: Serial2/0, Port ID (outgoing port): Serial2/0

Holdtime: 171

Version :

Cisco Internetwork Operating System Software

IOS (tm) PT1000 Software (PT1000-I-M), Version 12.2(28), RELEASE SOFTWARE (fc5)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2005 by cisco Systems, Inc.

Compiled Wed 27-Apr-04 19:01 by miwang

advertisement version: 2

Duplex: full

Ø  ROUTER2

R2#show cdp neighbors detail

Device ID: Switch

Entry address(es):

Platform: cisco PT3000, Capabilities: Switch

Interface: FastEthernet0/0, Port ID (outgoing port): FastEthernet0/1

Holdtime: 157

Version :

Cisco Internetwork Operating System Software

IOS (tm) PT3000 Software (PT3000-I6Q4L2-M), Version 12.1(22)EA4, RELEASE SOFTWARE (fc1)

Copyright (c) 1986-2006 by cisco Systems, Inc.

Compiled Fri 12-May-06 17:19 by pt_team

advertisement version: 2

Duplex: full

---------------------------

Device ID: R1

Entry address(es):

  IP address : 172.16.2.1

Platform: cisco PT1000, Capabilities: Router

Interface: Serial2/0, Port ID (outgoing port): Serial2/0

Holdtime: 121

Version :

Cisco Internetwork Operating System Software

IOS (tm) PT1000 Software (PT1000-I-M), Version 12.2(28), RELEASE SOFTWARE (fc5)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2005 by cisco Systems, Inc.

Compiled Wed 27-Apr-04 19:01 by miwang

advertisement version: 2

Duplex: full

---------------------------

Device ID: R3

Entry address(es):

  IP address : 192.168.1.1

Platform: cisco PT1000, Capabilities: Router

Interface: Serial3/0, Port ID (outgoing port): Serial3/0

Holdtime: 152

Version :

Cisco Internetwork Operating System Software

IOS (tm) PT1000 Software (PT1000-I-M), Version 12.2(28), RELEASE SOFTWARE (fc5)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2005 by cisco Systems, Inc.

Compiled Wed 27-Apr-04 19:01 by miwang

advertisement version: 2

Duplex: full

Ø  ROUTER3

R3#show cdp neighbors detail

Device ID: Switch

Entry address(es):

Platform: cisco PT3000, Capabilities: Switch

Interface: FastEthernet0/0, Port ID (outgoing port): FastEthernet0/1

Holdtime: 149

Version :

Cisco Internetwork Operating System Software

IOS (tm) PT3000 Software (PT3000-I6Q4L2-M), Version 12.1(22)EA4, RELEASE SOFTWARE (fc1)

Copyright (c) 1986-2006 by cisco Systems, Inc.

Compiled Fri 12-May-06 17:19 by pt_team

advertisement version: 2

Duplex: full

---------------------------

Device ID: R2

Entry address(es):

  IP address : 192.168.1.2

Platform: cisco PT1000, Capabilities: Router

Interface: Serial3/0, Port ID (outgoing port): Serial3/0

Holdtime: 171

Version :

Cisco Internetwork Operating System Software

IOS (tm) PT1000 Software (PT1000-I-M), Version 12.2(28), RELEASE SOFTWARE (fc5)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2005 by cisco Systems, Inc.

Compiled Wed 27-Apr-04 19:01 by miwang

advertisement version: 2

Duplex: full